Universal-remote-control-urs UR2-DTA Manuel d'utilisateur télécharger pdf

IMPORTANT SETUP NOTE!

This pertains to all programming steps.

When you are in setup mode, a compo-

nent LED will light for 20 seconds.If you do

not press a button within 20 seconds, the

LED light will turn off and exit setup mode

and you will need to start over.

A. Quick Set-Up Method

STEP1 Turn on the component you

want to program. To program

your TV, turn on the TV.

STEP2 Press and hold the [DEVICE] key

for 5 seconds until the POWER

LED will blink once and stays

on. Continue to hold the

[DEVICE] key and press the

number key assigned to your

brand in the Quick Set-up Code

Table and release both

[DEVICE] key and the number

key to save the code. The

POWER LED will blink twice to

confirm that the code is stored.

STEP3 Point the remote control at the

component.

STEP4 Press the power button. If it

turns off, it is programmed for

your component. If it does not

turn off, use the Pre-

Programmed 3-Digit code

Method or Scanning Method.

Repeat the steps above for all compo-

nents. (DTA, TV).

B. Quick Set-up Code Tables

C. Pre-Programmed 3-Digit Code

Method

STEP1 Turn on the Component you want

to program(TV, DTA).

STEP2 Press the [COMPONENT] button

(TV or DTA) to be programmed

and OK button simultaneously

for 3 seconds. The POWER LED

light will turn on for 20 seconds

indicating the unit is ready to be

programmed.

STEP3 Point the remote control toward

the Component and enter the 3-

digit code number assigned to

your brand.

*Note : If the 3-digit code number you just

entered is correct, the Component

will turn Off. If it did not turn Off,

continue entering code numbers

listed for that brand until the

Component turns Off.

STEP4 After you’ve entered the correct

code number and the Component

has turned Off, press the [POWER]

button to turn the Component

back On. Now it is time to test the

VOLUME and MUTE buttons for

the TV to make sure they all work.

If any of the functions do not work

as they should, repeat from STEP

3 using the next 3-digit code num-

ber listed for that brand until you

find the best code.

STEP5 Once you have found the correct

fy the code number, so you can

record it for future reference.

STEP1 Press the [COMPONENT] but-

ton (TV or DTA) you want to

verify and the OK button simul-

taneously for 3 seconds. The

POWER LED light will turn on

for 20 seconds.

STEP2 Press the [INFO] button and

count the number of times the

Component LED light blinks.

This number indicates the first

digit of the code, followed by

the second and third, each sep-

arated by a one second pause

when the LED will turn off.

*Note : 10 blinks represents the

number zero.

Example : One blink, (pause), eight

blinks, (pause) and three

blinks, indicates code

number 183.

F. Programming Volume Control

Volume and Mute control are factory-

programmed to automatically transfer

to the respective Component mode you

select, as follows:

DTA : DTA T V : TV

However, you can program the volume

controls (Volume Up, Volume Down

and Mute) from one Component to

operate in another Component.

If you wish to store the TV volume

control in DTA mode, use the follow-

ing steps.

STEP1 Press the [DTA] button and

the [OK] button simultane-

ously for 3 seconds.

The [DTA] Component LED

will turn on for 20 seconds.

3-digit code, save it by pressing

the same [COMPONENT] button

one more time. The POWER LED

light will blink twice to confirm that

the code was successfully stored.

D. Auto-Search Method

STEP1 Turn on the Component you

want to program (TV, DTA).

STEP2 Press the [COMPONENT] button

(TV or DTA) to be programmed

and OK button simultaneously

for 3 seconds. The POWER LED

light will turn on for 20 seconds

indicating the unit is ready to be

programmed.

STEP3 Point the remote toward the

Component and press the [CH5]

or [CH6] button one step at a

time or keep it pressed. The

remote will emit a series of

ON/OFF commands. Release the

[CH5] or [CH6] button as soon

as the Component turns Off.

STEP4 Test functions. (Same as for 3-

Digit Code Programming Method

- Section C). If any of the func-

tions do not work as they should,

repeat from STEP 3 using [CH5]

or [CH6] buttons to find the cor-

rect code.

STEP5

Save the code. (Same as for

3-Digit Code Programming

Method - Section C).

Now, repeat the Auto-Search Method

for those Components you could

not program earlier with the Pre-

Programmed Method.

E. Finding a Component Button’s

Setup Code Number

If you used the Auto-Search Method

to program a Component, you may

not know what the correct code num-

ber is. Here is a way for you to identi-

Button Functions

Programming the Remote Control

There are three ways you can program your remote:

* Quick Set-Up Method

* The Pre-Programmed 3-Digit Code Method

* The Auto-Search Method

The Quick Set-Up Method is a unique new feature that enables the fastest and

easiest set-up by using one-digit codes for up to 10 major brands for each compo-

nent.

The Pre-Programmed Code Method allows you to setup all the buttons at once by

entering 3-digit code numbers that correspond to a particular Component’s manu-

facturer/brand, so it’s the fastest and easiest of the two methods. (Code Tables

are on the backside of this Instruction Sheet.) The Auto-Search Method scans

through all the codes in the remote control, one at a time.

Universal Remote Control, Inc.

www.universalremote.com

OCE-0089A REV 14 (14/03/14)

Operating Instructions For

UR2-DTA

DTA Remote Control

The UR2-DTA is designed to

operate the S/A, Pace Micro,

Motorola and IPTV set tops, plus

the majority of TV equipment on

the market as shown below.

DTA : DTA boxs, IPTV set tops

TV : Televisions

Introduction

Volume Default: TV volume and mute

through The TV, with the option of con-

trolling volume and mute through the

Cable. Refer to Section F For program-

ming the volume and mute through

your Cable.

Operations

Replacing Batteries

Before you program or operate the

remote control, you must install two new

AA alkaline batteries.

STEP1 Remove the battery compart-

ment cover on the back of your

remote control.

STEP2 Check battery polarity carefully,

and install the batteries as

shown in the illustration below.

STEP3 Replace the battery compart-

ment cover.

Quick Number

Manufacturer/Brand

0 SANYO

1 SONY

2 SAMSUNG

3LG

4 TOSHIBA

5 PANASONIC

6 PHILIPS

7 HITACHI

8 SHARP

9 VIZIO

Quick Number

Manufacturer/Brand

DTA

0 PACE DTA

SA/CISCO, SAMSUNG, PACE DIGITAL

2 MOTOROLA DIGITAL

3 MOTOROLA DTA

4 EVOLUTION DTA

5 CISCO IPTV

6 ADB IPTV

7 TECHNICOLOR

8 AMINO 140/540 IPTV

9 MOTOROLA IPTV

1 2

Résumé du contenu

Page 1 - DTA Remote Control

IMPORTANT SETUP NOTE! This pertains to all programming steps.When you are in setup mode, a compo-nent LED will light for 20 seconds.If you donot press

Page 2 - Set-up Code Tables

Manufacturer/BrandSet-Up Code NumberTVManufacturer/BrandSet-Up Code NumberDTA-CABLE ConvertersSet-up Code Tables6CINCINNATI BELL194CISCO 003 005CONFLU

Commentaires sur ces manuels

Pas de commentaire

Universal-remote-control-urs UR2-DTA Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Contrôle à distance Universal-remote-control-urs UR2-DTA. Universal Remote Control (URS) UR2-DTA User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Contrôle à distance Universal-remote-control-urs UR2-DTA